Filament Guide
ASA Filament Guide
ABS done right. UV-stable, heat-resistant, outdoor-ready.
Last updated: March 2026
ASA
Acrylonitrile Styrene Acrylate
ABS done right. UV-stable, heat-resistant, outdoor-ready.
Intermediate
Outdoor Specialist
ASA swaps the UV-unstable butadiene in ABS for acrylate rubber[1] — same heat resistance, same toughness, but it won't yellow or crack after years in direct sunlight. It's what you use for anything that lives outside: garden fixtures, car trim, camera mounts, signage.
Still warps like ABS, still stinks. Enclosure and ventilation required. But if your part needs heat resistance or outdoor durability, ASA beats ABS in every way except acetone smoothing doesn't work as cleanly.
Chemistry
Terpolymer: acrylonitrile + styrene + acrylate rubber (replaces butadiene in ABS)
Print Temp
Heat Resistance
Softens at ~100°C[2] - same as ABS
UV Resistance
Excellent - designed for continuous outdoor exposure, years of stability
vs ABS
Better UV, similar heat/strength. No vapor smoothing
Fumes
Styrene fumes - same precautions as ABS
Pros
- Outstanding UV and weathering resistance
- High heat resistance (~100°C)
- Tough and impact-resistant
- Color-stable outdoors for years
- Good chemical resistance
Cons
- Warps - enclosure strongly recommended
- Emits fumes - ventilation needed
- More expensive than ABS or PETG
- Acetone vapor smoothing works but less cleanly than ABS
- Fewer color options than PLA/PETG
Best Used For
Outdoor signage
Garden fixtures
Automotive exterior
Drone frames
Weatherproof enclosures
Marine components
Antenna mounts
Niche Tips
ASA can be glued with MEK (methyl ethyl ketone) or acetone-based glues for a chemical weld - stronger than mechanical fasteners on small parts.
Brim is your friend. ASA warps at corners. 5-10mm brim + slow first layer (15-20mm/s) cuts warp failures way down.
ASA's color stability is its key feature - blacks stay black, whites stay white. UV-exposed PLA turns yellow; UV-exposed ASA barely changes after 2 years outdoors.
Storage & Humidity
Target: below 25% RH. ASA absorbs moisture similarly to ABS. Given that ASA is often chosen for outdoor applications, proper drying is especially important - moisture-weakened parts won't hold up in the field.
Drying: 60-80°C for 4-6 hours. Same approach as ABS.
Bed Adhesion
Best surfaces: PEI with glue stick, glass with hairspray. ASA is similar to ABS in adhesion behavior.
Recommended bed temp: 90-110°C. An enclosure is strongly recommended - ASA warps less than ABS but still significantly. A brim helps for large flat prints.
ASA can be solvent-bonded with acetone for joining parts, though it does not vapor-smooth as cleanly as ABS.
Variants & Special Types
ASA-CFASA with carbon fiber. Combines UV resistance with increased stiffness. The go-to for outdoor structural applications that need rigidity. Hardened nozzle required.
ASA-GFASA with glass fiber. Better impact resistance than CF, less stiff but tougher. Good for outdoor parts that need to survive impacts.
References
- Prusa Knowledge Base - ASA. UV resistance, print temperatures, and comparison to ABS. help.prusa3d.com/article/asa_2070
- Bambu Lab Wiki - Filament Guide Material Table. Glass transition temperatures and printing parameters for common filaments. wiki.bambulab.com/en/general/filament-guide-material-table
Recommended Gear
Enclosure
3D printer enclosure
ASA warps as aggressively as ABS without an enclosure. Essential for consistent results and fume containment.
CHECK PRICE →
Dryer
Filament dryer
ASA is moderately hygroscopic. Dry at 65-80°C for 4 hours before printing for best results.
CHECK PRICE →
Frequently Asked Questions
Is ASA better than ABS for outdoor use?
Yes. ASA was specifically developed as a UV-stable alternative to ABS. It resists yellowing and degradation from sunlight far better than ABS, which becomes brittle and discolored after prolonged UV exposure. For any part that will live outdoors permanently, ASA is the clear choice over ABS.
Does ASA smell when printing?
Yes, ASA emits a noticeable odor during printing, similar to ABS. It releases VOCs including styrene and ultrafine particles. An enclosure with a carbon filter or good room ventilation is recommended. Do not print ASA in unventilated spaces or bedrooms.
Can ASA be acetone smoothed?
Yes. Like ABS, ASA dissolves in acetone and can be vapor smoothed using the same technique - placing the part in a sealed container with acetone fumes for 15-30 minutes. The result is a smooth, glossy surface with eliminated layer lines. Acetone also works as a solvent weld for bonding ASA parts together.
Does ASA need an enclosure?
Yes. ASA warps similarly to ABS and benefits significantly from an enclosed build chamber. The enclosure maintains stable ambient temperature and prevents drafts from causing uneven cooling. Without an enclosure, expect warping and layer adhesion issues on all but the smallest prints.