Best Filament for the Flashforge Adventurer 5M
Open-frame 220 mm cube with a 280 C direct-drive hotend: a PLA and PETG workhorse that needs a nozzle swap before you touch anything filled.
Specs verified 2026-11 · prices refreshed daily · page updated 6 November 2026
The Flashforge Adventurer 5M is an open-frame printer with a 220 x 220 x 220 mm build volume and a hotend reaching 280°C. It handles PLA, PETG and TPU, and it needs a hardened nozzle before running carbon- or glass-fibre filament. Recommended materials: PLA, PLA+, PETG, TPU.
The Adventurer 5M is an open-frame CoreXY with a 220 x 220 x 220 mm build area, a 280 C direct-drive hotend and a 100 C PEI-coated flex plate. Flashforge's own supported-material list for the machine is short and honest: PLA and PETG on the stock 0.4 mm nozzle, with TPU, PLA-CF and PETG-CF moved to the 0.6 mm nozzle. There is no enclosure and no chamber heater, so ABS and ASA are not on that list. You can run them if you cover the printer, but layer adhesion and warping on tall parts will be a lottery, and the 100 C bed is the only heat you get.
What the Flashforge Adventurer 5M prints well
Recommended materials for this printer:
No enclosure, so ABS, ASA, PC and nylon will warp and crack. Stick to PLA, PLA+, PETG and TPU for reliable prints. Carbon- and glass-fibre composites also need a hardened nozzle first.
The stock nozzle is the detail most buyers miss. Flashforge's own parts listings describe the 0.25 mm and 0.4 mm assemblies as brass alloy with a stainless steel tip and say outright that they are not suitable for particle-filled or fibre-reinforced filament. The 0.6 mm and 0.8 mm assemblies are the hardened steel ones. So a spool of PLA-CF or PETG-CF on the shipped 0.4 mm nozzle will round out the orifice within a kilo or two. Budget roughly $35 to $39 for a 0.6 mm hardened assembly before you buy carbon-filled filament, and treat 0.6 mm as the permanent abrasive nozzle rather than swapping back and forth.
Flashforge Adventurer 5M specs that affect filament
For flexibles, the direct-drive extruder is the right layout, and Flashforge lists TPU on the 0.6 mm nozzle. Print TPU 95A at 20 to 30 mm/s with retraction near zero and the spool mounted so the filament path has no tight bend. Drying matters more than it does on an enclosed machine because an open frame gives you no warm air at all: PETG, TPU and nylon-adjacent composites all want 4 to 6 hours at 45 to 55 C before a long job. The 0.4 mm nozzle is the one you keep for PLA, matte PLA, silk PLA and PETG, which is most of what this printer is for.
Filament notes for the Flashforge Adventurer 5M
- PLA, PLA+ and matte or silk PLA are the native fit: 205 to 220 C nozzle, 55 to 60 C bed, no enclosure needed.
- PETG runs well at 235 to 250 C with the bed at 75 to 85 C, but drop fan speed to 30 to 50 percent or the layers will not bond.
- ABS and ASA are not on Flashforge's supported list for the 5M because the frame is open; the optional enclosure kit (about $40) helps but adds no active heat.
- The shipped 0.4 mm nozzle is brass with a stainless tip and is explicitly not rated for fibre-filled filament, so PLA-CF and PETG-CF need the hardened 0.6 mm assembly.
- TPU 95A works on the direct-drive extruder at 20 to 30 mm/s through the 0.6 mm nozzle; softer 85A is a stretch on any Bowden-free path at this flow.
- The 280 C hotend ceiling rules out PC, PA6 and PPS-class filament regardless of what nozzle you fit.
- With no heated chamber to dry the air, dry PETG and TPU for 4 to 6 hours at 45 to 55 C before any print over about three hours.
The deals above are filtered to the materials the Flashforge Adventurer 5M handles, aggregated from multiple retailers daily and normalised to cost per kg, so the cheapest in-stock option is always on top. Prices refresh every 24 hours and are region-aware, so switch your region in the nav. Click through to the retailer to confirm the live checkout price.
Frequently Asked Questions
Different printer? See filament by printer for the rest of the lineup, or browse cheapest filament by material.