Best Filament for the Sovol SV08
A pre-built Voron 2.4 clone running vanilla Klipper, with 350 × 350 × 345 mm of open-frame volume for PLA, PETG and TPU.
Specs verified 2026-11 · prices refreshed daily · page updated 6 November 2026
The Sovol SV08 is an open-frame printer with a 350 × 350 × 345 mm build volume and a hotend reaching 300°C. It handles PLA, PETG and TPU, and it needs a hardened nozzle before running carbon- or glass-fibre filament. Recommended materials: PLA, PLA+, PETG, TPU.
The SV08 is a semi-assembled Voron 2.4 with injection-moulded parts, and its filament envelope is set by three numbers: a 300 C nozzle, a 100 C bed and no enclosure. That makes it a very large PLA, PETG and TPU printer rather than an engineering-material machine. Sovol's own supported list reads PLA, PETG, TPU, PETG-CF and ABS, while Tom's Hardware recorded the practical set as PLA, PETG and TPU up to 300 C. The 350 × 350 × 345 mm volume is the draw, and a 100 C bed gets ABS to stick, but an open flying-gantry frame will not hold the air temperature a 300 mm ABS part needs.
What the Sovol SV08 prints well
Recommended materials for this printer:
No enclosure, so ABS, ASA, PC and nylon will warp and crack. Stick to PLA, PLA+, PETG and TPU for reliable prints. Carbon- and glass-fibre composites also need a hardened nozzle first.
The stock nozzle is the thing to know before buying CF filament. Sovol's own replacement hotend kit for the SV08 specifies a titanium alloy throat with a copper alloy heating block and a copper alloy 0.4 mm nozzle, and the store sells a separate SKD11 hardened steel kit for around $30 as an upgrade. Copper alloy is soft, so chopped carbon or glass fibre will open the orifice out of spec within a couple of spools. Fit the hardened kit first if PETG-CF or PLA-CF is on your list, and go 0.6 mm while you are in there. Sovol's own note on that kit is to raise PLA to 245 C with the hardened nozzle.
Sovol SV08 specs that affect filament
Flexibles and tuning are where the SV08 rewards effort. The planetary dual-gear direct drive handles 95A TPU well because the filament path from gear to melt zone is short, and vanilla Klipper means you edit your own pressure advance and flow for every material instead of waiting for a vendor profile. The flip side is the shipped profiles are conservative, and the PEI plate needed glue stick for high-speed prints in testing. Rated speed is 700 mm/s at 40,000 mm/s², but flow caps at 30 mm³/s, so wall speed on a 0.4 mm nozzle is the real limit, not motion. A $179 glass enclosure kit exists and improves ABS slightly, but it adds no chamber heater.
Filament notes for the Sovol SV08
- PLA, PETG and TPU are the intended set; the 300 C nozzle and 100 C bed are the hard ceilings.
- The stock 0.4 mm nozzle is copper alloy, so carbon-fibre and glass-fibre filament needs the SKD11 hardened kit first.
- ABS and ASA will stick to the 100 C bed but warp on large parts because the frame is open and unheated.
- The optional glass enclosure kit holds some heat but adds no chamber heater, so treat ABS as small parts only.
- Planetary dual-gear direct drive feeds 95A TPU reliably; drop speed to roughly 50 mm/s and dry it first.
- Flow is capped at 30 mm³/s, so a 0.6 mm nozzle is how you actually use the 700 mm/s motion rating.
- Vanilla Klipper means you tune your own filament profiles, and the shipped OrcaSlicer presets are conservative.
The deals above are filtered to the materials the Sovol SV08 handles, aggregated from multiple retailers daily and normalised to cost per kg, so the cheapest in-stock option is always on top. Prices refresh every 24 hours and are region-aware, so switch your region in the nav. Click through to the retailer to confirm the live checkout price.
Frequently Asked Questions
Different printer? See filament by printer for the rest of the lineup, or browse cheapest filament by material.